Home / Frigidaire Dishwasher Repair in Winnipeg

Frigidaire Dishwasher Repair in Winnipeg

Reviewed October 2026 · Winnipeg, Manitoba

$150 to $400most Frigidaire dishwasher repairs
Same-daymost Winnipeg calls
Best fori20, i40, CL and Cd codes

Frigidaire dishwasher repair in Winnipeg usually runs $150 to $400 in parts and labour, and on a lot of calls the first fix costs nothing. An i20 on the display means the tub did not drain, an i40 means the filter or sump is packed with food, and CL or Cd means the door never latched. Those three account for most of the Frigidaire dishwashers we are asked about, and Frigidaire's own steps for each are below. When a part has failed, a latch, inlet valve or drain pump sits near the bottom of the range and a wash pump or control board near the top. We book same-day or next-day across the city, Gallery and Professional models included, and you hear the price before any panel comes off. For other makes, start at dishwasher repair Winnipeg.

(431) 441-3572

Need it today? Call

(431) 441-3572

We book a real arrival window across Winnipeg, diagnose the fault, and quote a firm price before any work.

  • Same-day & next-day service
  • Firm price before any work
  • Service call credited to the repair
  • All major brands, one-visit repairs
Call (431) 441-3572

Winnipeg & surrounding area

Book a repair

Tell us what’s broken and we’ll come back the same business day with a time and a price.

No obligation. The price is quoted before any work. Your details go only to our Winnipeg team.

What the Frigidaire display is telling you

Frigidaire keeps a short list of dishwasher codes on its Canadian dishwasher error code guide. Half of what appears on the display is not a fault at all, so it is worth sorting the codes into two piles before anyone books a visit.

What you see What Frigidaire says it means What usually happens next
i20 The dishwasher did not drain completely Free if it is the hose, knockout plug or glass trap; $180 to $350 if the drain pump has failed
i40 Food soil has clogged the filter or sump Clean the glass trap and filter, then rerun; a visit only if it keeps coming back
CL or Cd The door has not closed and latched Free if something is in the way; $150 to $280 for a latch or door switch
PF The power was interrupted Press START/CANCEL and start a new cycle
Hd or HO The heater is warming the water before the wash Normal; it takes longer when the incoming water is cold
LOC The door is locked Normal
01 to 24 A delayed start is counting down Normal; press cancel to start now
1 to 199 Minutes left in the cycle Normal
PRESS START Close the door within 5 seconds of pressing start Normal

Codes that are not on that list vary by model, and the owner's manual is the authority for those. When you call, read us the exact characters on the display and whether anything is flashing. That tells the technician which part to bring.

i20: the Frigidaire that leaves water in the tub

An i20 is the drain code, and Frigidaire's i20 article lists five things to check before anyone touches the pump. We go through them in the same order on a Winnipeg call, because the first four are free.

  1. The knockout plug. A new garburator ships with a plug sealed into the dishwasher inlet. If the garburator was replaced recently and the dishwasher has never drained properly since, this is almost always the reason. The plug has to be knocked out from inside the garburator inlet.
  2. A blocked hose. Food, grease and fruit labels collect where the drain hose joins the garburator or the sink tailpiece. Running the garburator for a few seconds clears the easy ones.
  3. A pinched hose. Cleaning bottles, a bin or a water filter cartridge pushed against the hose under the sink can squeeze it nearly flat.
  4. Hose height. Frigidaire asks for the drain hose to rise at least 32 inches off the floor before it drops to the drain. A hose that runs flat along the cabinet floor lets dirty sink water drift back into the tub, which looks exactly like a dishwasher that will not drain.
  5. The glass trap and filter. Clear the food out of both. More on that in the next section.

Frigidaire says the i20 can be cleared by pressing and holding cancel, by switching the dishwasher off at the breaker, or by unplugging it for 3 minutes. Clear it only after you have done the checks, or it comes straight back on the next load.

If every check passes and the tub still holds water, listen while you cancel a cycle. A pump that hums but moves no water is jammed, often by a piece of glass or a cherry pit, and can sometimes be freed. A pump that makes no sound at all has usually failed electrically. A replacement drain pump is $180 to $350 installed. The same checks for any brand are laid out step by step on dishwasher not draining.

i40 and the glass trap: a Frigidaire design worth knowing

Many Frigidaire dishwashers use a filter you clean by hand rather than a self-cleaning grinder. The filter sits in the tub floor under the lower spray arm, and Frigidaire calls the part that catches large debris the glass trap. Shards of a broken glass, bits of label, seeds and bones end up there by design, so they do not reach the pump.

The trade-off is that the trap and filter need emptying. When they fill, the water cannot reach the pump fast enough, washing gets poor, and the dishwasher eventually throws i40. Frigidaire's fix is simple: clean the glass trap and filter and run the dishwasher again. If i40 returns after a clean filter, that is when a technician looks at the sump and the pump.

How often to clean it depends on the household. A family that scrapes but does not rinse plates may need to empty the trap every week or two. Two people who rinse first can go a month or more. If the dishwasher smells sour when you open it the morning after a cycle, the trap is usually overdue.

CL or Cd: the door that will not latch

If CL or Cd is on the display, the dishwasher believes the door is open and will not run. Frigidaire's instruction is to close and latch the door firmly, and to contact service if it will not close.

Before calling, check three things:

  • A rack or tall item in the way. A cookie sheet or a cutting board on the bottom rack can stop the door a few millimetres short.
  • The rack rollers. A lower rack that has jumped its track sits too far forward.
  • The cabinet. A dishwasher that has slid forward because its mounting brackets came loose from the counter will not line up with its own latch. Look for this in any kitchen where the counter has been replaced, because the brackets are often never refastened afterwards.

If the door closes cleanly and the code stays, the latch assembly or the door switch inside it has failed. That is a $150 to $280 repair and is usually done in one visit.

Hd, HO and a long first cycle in January

Hd or HO means the dishwasher is heating its water before it starts washing. Frigidaire says the delay runs about 1 to 2 minutes for every degree the water has to rise, so the colder the water arriving at the machine, the longer the wait. That is why many Winnipeg households notice their dishwasher taking noticeably longer in the depth of winter: the water reaching the house is colder, and a supply line that runs along an outside wall or through a cold crawlspace cools it further.

It is not a fault. Two habits shorten it: run the kitchen tap until it comes out hot before you press start, and keep the cabinet under the sink open on the coldest nights. The City of Winnipeg's frozen pipe prevention advice recommends opening kitchen, bathroom and laundry cabinets so warm air reaches the plumbing, and keeping the thermostat no lower than 12°C at night and when you are away. A dishwasher supply line that actually freezes will stop the machine filling at all, which is a different problem from Hd.

If Hd sits on the display for a very long time and the water never gets warm, the heating element or the temperature sensor is the likely part, and we quote it by model after testing.

Leaks under a Frigidaire dishwasher

A puddle at the front edge of the door almost always comes from the door gasket or the lower door seal, or from suds. Hand dish soap in the dispenser, or too much rinse aid, foams up and pushes water past a perfectly good seal. An empty rinse cycle and a towel fix that one.

A puddle that appears from underneath, with the door edge dry, is more often a hose joint, the inlet valve connection, or the pump seal. On a kitchen floor over a finished basement in River Heights, Wolseley or St. Boniface, that is worth stopping quickly: turn off the shut-off valve under the sink and switch the dishwasher off at the breaker until it has been looked at. Some Frigidaire models show a leak code of their own; read it to us exactly as it appears. A seal, gasket or hose joint is usually $150 to $300, and a leak from the pump seal can approach $400 because the pump comes out as part of the job.

Dishes coming out dirty

Poor washing on a Frigidaire usually comes down to one of four things, and most are free:

  • A full glass trap and filter. The single most common cause. Clean them first.
  • Blocked spray arms. Pull the arms, look through the holes against the light, and clear them with a toothpick. Check the arms spin freely by hand and that nothing on the rack stops them.
  • Scale on the jets. The City of Winnipeg's published water test results put total hardness at an average of 82 mg/L. That is moderate, so scale builds over years rather than months, but a monthly cleaning cycle keeps the jets open.
  • A weak wash pump. If the filter and arms are clean and you can hear the motor but barely any water moves, the circulation pump is the part, $220 to $400.

Frigidaire dishwasher repair costs in Winnipeg

Frigidaire parts are priced like any mainstream dishwasher's, so the published ranges are the same ones we use for every brand.

Frigidaire dishwasher repair Typical range
Door latch or door switch (CL, Cd) $150 to $280
Door gasket or lower door seal $150 to $280
Water inlet valve (will not fill, slow fill) $160 to $300
Drain pump (i20 that the checks do not clear) $180 to $350
Circulation or wash pump (poor washing) $220 to $400
Control board or touchpad $200 to $400

The diagnostic visit is typically $90 to $130 and is credited to the repair if you go ahead. Every dishwasher part and symptom, priced for Winnipeg, is on dishwasher repair cost Winnipeg.

Repair or replace a Frigidaire dishwasher

Frigidaire sits at the affordable end of the dishwasher floor, and that moves the repair-or-replace line earlier than it would be on a premium machine. Our rule of thumb:

  • Under about 5 years old: repair almost anything. A latch, valve, seal or drain pump on a young machine is an easy yes.
  • 5 to 8 years old: repair the inexpensive parts without much thought. For a wash pump or a control board, compare the quote with the price of the replacement you would actually buy.
  • Past 8 years: a latch or valve is still usually worth doing if the tub, racks and door are in good shape. A board or pump at the top of the range, on a machine with rusting racks, usually is not.

You get the figure and a straight opinion before anything is ordered. The repair-or-replace calculator runs the same arithmetic on your own numbers. If you have other Frigidaire appliances in the house, the brand-wide guide is Frigidaire appliance repair Winnipeg.

Before you book

  • Write down the code exactly as it shows, and whether anything is flashing.
  • Empty the glass trap and filter and rerun the cycle.
  • Check the drain hose rises at least 32 inches and is not crushed under the sink.
  • If the garburator is new, confirm the knockout plug was removed.
  • Find the model and serial number. On most Frigidaire dishwashers the label is on the inner edge of the door or the side of the tub opening. Read it to us when you call.
  • Check for recalls by searching your model on Health Canada's Recalls and Safety Alerts site.

Questions we get asked

How much does Frigidaire dishwasher repair cost in Winnipeg?

Most Frigidaire dishwasher repairs in Winnipeg cost $150 to $400 in parts and labour. A latch, seal, inlet valve or drain pump is at the lower end, and a wash pump or control board at the top. The $90 to $130 diagnostic visit is credited to the repair if you go ahead.

What does i20 mean on a Frigidaire dishwasher?

The dishwasher did not drain completely. Frigidaire says to check that the garburator knockout plug is removed, the drain hose is not blocked or pinched and rises at least 32 inches off the floor, and the glass trap and filter are clear. If all of that is fine, the drain pump is the likely part.

How do I clear an i40 code on my Frigidaire?

Clean the glass trap and the filter in the floor of the tub, then run the dishwasher again. Frigidaire says i40 means food soil has built up in the filter or sump. If the code returns with a clean filter, have the sump and pump checked.

Why does my Frigidaire dishwasher say CL or Cd?

It thinks the door is not closed and latched. Close it firmly and check that a rack, a tall item or loose mounting brackets are not stopping it. If the door shuts properly and the code stays, the latch or door switch needs replacing.

Why does my Frigidaire show Hd for so long?

Hd means it is heating the water before washing, and Frigidaire puts that at about 1 to 2 minutes per degree of rise. In a Winnipeg winter the incoming water is colder, so the wait is longer. Running the tap hot before you start shortens it.

How do I reset a Frigidaire dishwasher?

For a drain code, Frigidaire lists pressing and holding cancel, switching the breaker off, or unplugging the dishwasher for 3 minutes. Do the checks first, because a reset without fixing the cause just brings the code back.

Are you Frigidaire's factory service?

No. We are an independent repair service and are not affiliated with Frigidaire or Electrolux. If your dishwasher is still under the manufacturer's warranty, contact Frigidaire first so your coverage is not affected. Out of warranty, we are usually the faster way to get it working.

Reviewed October 2026.

(431) 441-3572

Need it today? Call

(431) 441-3572

We book a real arrival window across Winnipeg, diagnose the fault, and quote a firm price before any work.

  • Same-day & next-day service
  • Firm price before any work
  • Service call credited to the repair
  • All major brands, one-visit repairs
Call (431) 441-3572

Winnipeg & surrounding area

Book a repair

Tell us what’s broken and we’ll come back the same business day with a time and a price.

No obligation. The price is quoted before any work. Your details go only to our Winnipeg team.

Broken appliance? Let's get it running.

Same-day service across Winnipeg. Straight pricing, quoted before any work.

Call nowGet a quoteRepair or replace?